This patch adds support for the BPF V4 ISA byte swap instructions to
opcodes, assembler and disassembler.
Tested in bpf-unknown-none.
include/ChangeLog:
2023-07-24 Jose E. Marchesi <jose.marchesi@oracle.com>
* opcode/bpf.h (BPF_IMM32_BSWAP16): Define.
(BPF_IMM32_BSWAP32): Likewise.
(BPF_IMM32_BSWAP64): Likewise.
(enum bpf_insn_id): New entries BPF_INSN_BSWAP{16,32,64}.
opcodes/ChangeLog:
2023-07-24 Jose E. Marchesi <jose.marchesi@oracle.com>
* bpf-opc.c (bpf_opcodes): Add entries for the BSWAP*
instructions.
gas/ChangeLog:
2023-07-24 Jose E. Marchesi <jose.marchesi@oracle.com>
* doc/c-bpf.texi (BPF Instructions): Document BSWAP* instructions.
* testsuite/gas/bpf/alu.s: Test BSWAP{16,32,64} instructions.
* testsuite/gas/bpf/alu.d: Likewise.
* testsuite/gas/bpf/alu-be.d: Likewise.
* testsuite/gas/bpf/alu-pseudoc.s: Likewise.
* testsuite/gas/bpf/alu-pseudoc.d: Likewise.
* testsuite/gas/bpf/alu-be-pseudoc.d: Likewise.
This patch fixes the pseudoc syntax of the V4 instructions MOVS* and
LDXS* in order to reflect https://reviews.llvm.org/D144829.
opcodes/ChangeLog:
2023-07-24 Jose E. Marchesi <jose.marchesi@oracle.com>
* bpf-opc.c (bpf_opcodes): Fix pseudo-c syntax for MOVS* and LDXS*
instructions.
gas/ChangeLog:
2023-07-24 Jose E. Marchesi <jose.marchesi@oracle.com>
* doc/c-bpf.texi (BPF Instructions): Fix pseudoc syntax for MOVS*
and LDXS* instructions.
* testsuite/gas/bpf/mem-pseudoc.d: Likewise.
* testsuite/gas/bpf/mem-be-pseudoc.d: Likewise.
* testsuite/gas/bpf/mem-pseudoc.s: Likewise.
* testsuite/gas/bpf/alu-pseudoc.s: Likewise.
* testsuite/gas/bpf/alu-pseudoc.d: Likewise.
* testsuite/gas/bpf/alu-be-pseudoc.d: Likewise.
* testsuite/gas/bpf/alu32-pseudoc.s: Likewise.
* testsuite/gas/bpf/alu32-pseudoc.d: Likewise.
* testsuite/gas/bpf/alu32-be-pseudoc.d: Likewise.
This patch adds support for the V4 BPF instruction jal/gotol, which is
like ja/goto but it supports a signed 32-bit PC-relative (in number of
64-bit words minus one) target operand instead of the 16-bit signed
operand of the other instruction. This greatly increases the jump
range in BPF programs.
Tested in bpf-unkown-none.
bfd/ChangeLog:
2023-07-24 Jose E. Marchesi <jose.marchesi@oracle.com>
* reloc.c: New reloc BFD_RELOC_BPF_DISPCALL32.
* elf64-bpf.c (bpf_reloc_type_lookup): Handle the new reloc.
* libbfd.h (bfd_reloc_code_real_names): Regenerate.
gas/ChangeLog:
2023-07-24 Jose E. Marchesi <jose.marchesi@oracle.com>
* config/tc-bpf.c (struct bpf_insn): New field `id'.
(md_assemble): Save the ids of successfully parsed instructions
and use the new BFD_RELOC_BPF_DISPCALL32 whenever appropriate.
(md_apply_fix): Adapt to the new BFD reloc.
* testsuite/gas/bpf/jump.s: Test JAL.
* testsuite/gas/bpf/jump.d: Likewise.
* testsuite/gas/bpf/jump-pseudoc.d: Likewise.
* testsuite/gas/bpf/jump-be.d: Likewise.
* testsuite/gas/bpf/jump-be-pseudoc.d: Likewise.
* doc/c-bpf.texi (BPF Instructions): Document new instruction
jal/gotol.
Document new operand type disp32.
include/ChangeLog:
2023-07-24 Jose E. Marchesi <jose.marchesi@oracle.com>
* opcode/bpf.h (enum bpf_insn_id): Add entry BPF_INSN_JAL.
(enum bpf_insn_id): Remove spurious entry BPF_INSN_CALLI.
opcodes/ChangeLog:
2023-07-23 Jose E. Marchesi <jose.marchesi@oracle.com>
* bpf-opc.c (bpf_opcodes): Add entry for jal.
This tiny patch makes the BPF disassembler to emit, e.g.
ldxdw %r1, [%r0+0]
instead of
ldxdw %r1, [%r00]
when the offset is 0, to avoid confusion.
opcodes/
* bpf-dis.c (print_insn_bpf): Print offsets with value 0 as "+0".
gas/
* testsuite/gas/bpf/mem.s: Add tests with offset 0.
* testsuite/gas/bpf/mem-pseudoc.s: Likewise.
* testsuite/gas/bpf/mem.d: Update accordingly.
* testsuite/gas/bpf/mem-be.d: Likewise.
* testsuite/gas/bpf/mem-pseudoc.d: Likewise.
* testsuite/gas/bpf/mem-be-pseudoc.d: Likewise.
This commit adds the signed load to register (ldxs*) instructions
introduced in the BPF ISA version 4, including opcodes and assembler
tests.
Tested in bpf-unknown-none.
include/ChangeLog:
2023-07-21 Jose E. Marchesi <jose.marchesi@oracle.com>
* opcode/bpf.h (enum bpf_insn_id): Add entries for signed load
instructions.
(BPF_MODE_SMEM): Define.
opcodes/ChangeLog:
2023-07-21 Jose E. Marchesi <jose.marchesi@oracle.com>
* bpf-opc.c (bpf_opcodes): Add entries for LDXS{B,W,H,DW}
instructions.
gas/ChangeLog:
2023-07-21 Jose E. Marchesi <jose.marchesi@oracle.com>
* testsuite/gas/bpf/mem.s: Add signed load instructions.
* testsuite/gas/bpf/mem-pseudoc.s: Likewise.
* testsuite/gas/bpf/mem.d: Likewise.
* testsuite/gas/bpf/mem-pseudoc.d: Likewise.
* testsuite/gas/bpf/mem-be.d: Likewise.
* doc/c-bpf.texi (BPF Instructions): Document the signed load
instructions.
This commit adds the signed register move (movs) instructions
introduced in the BPF ISA version 4, including opcodes and assembler
tests.
Tested in bpf-unknown-none.
include/ChangeLog:
2023-07-21 Jose E. Marchesi <jose.marchesi@oracle.com>
* opcode/bpf.h (BPF_OFFSET16_MOVS8): Define.
(BPF_OFFSET16_MOVS16): Likewise.
(BPF_OFFSET16_MOVS32): Likewise.
(enum bpf_insn_id): Add entries for MOVS{8,16,32}R and
MOVS32{8,16,32}R.
opcodes/ChangeLog:
2023-07-21 Jose E. Marchesi <jose.marchesi@oracle.com>
* bpf-opc.c (bpf_opcodes): Add entries for MOVS{8,16,32}R and
MOVS32{8,16,32}R instructions. and MOVS32I instructions.
gas/ChangeLog:
2023-07-21 Jose E. Marchesi <jose.marchesi@oracle.com>
* testsuite/gas/bpf/alu.s: Test movs instructions.
* testsuite/gas/bpf/alu-pseudoc.s: Likewise.
* testsuite/gas/bpf/alu32.s: Likewise for movs32 instruction.
* testsuite/gas/bpf/alu32-pseudoc.s: Likewise.
* testsuite/gas/bpf/alu.d: Add expected results.
* testsuite/gas/bpf/alu32.d: Likewise.
* testsuite/gas/bpf/alu-be.d: Likewise.
* testsuite/gas/bpf/alu32-be.d: Likewise.
* testsuite/gas/bpf/alu-pseudoc.d: Likewise.
* testsuite/gas/bpf/alu32-pseudoc.d: Likewise.
* testsuite/gas/bpf/alu-be-pseudoc.d: Likewise.
* testsuite/gas/bpf/alu32-be-pseudoc.d: Likewise.
This was breaking --enable-targets=all builds.
opcodes/ChangeLog:
2023-07-21 Jose E. Marchesi <jose.marchesi@oracle.com>
* Makefile.am (TARGET64_LIBOPCODES_CFILES): Add missing bpf-dis.c
* Makefile.in: Regenerate.
CGEN is cool, but the BPF architecture is simply too bizarre for it.
The weird way of BPF to handle endianness in instruction encoding, the
weird C-like alternative assembly syntax, the weird abuse of
multi-byte (or infra-byte) instruction fields as opcodes, the unusual
presence of opcodes beyond the first 32-bits of some instructions, are
all examples of what makes it a PITA to continue using CGEN for this
port. The bpf.cpu file is becoming so complex and so nested with
p-macros that it is very difficult to read, and quite challenging to
update. Also, every time we are forced to change something in CGEN to
accommodate BPF requirements (which is often) we have to do extensive
testing to make sure we do not break any other target using CGEN.
This is getting un-maintenable.
So I have decided to bite the bullet and revamp/rewrite the port so it
no longer uses CGEN. Overall, this involved:
* To remove the cpu/bpf.{cpu,opc} descriptions.
* To remove the CGEN generated files.
* To replace the CGEN generated opcodes table with a new hand-written
opcodes table for BPF.
* To replace the CGEN generated disassembler wih a new disassembler
that uses the new opcodes.
* To replace the CGEN generated assembler with a new assembler that uses the
new opcodes.
* To replace the CGEN generated simulator with a new simulator that uses the
new opcodes. [This is pushed in GDB in another patch.]
* To adapt the build systems to the new situation.
Additionally, this patch introduces some extensions and improvements:
* A new BPF relocation BPF_RELOC_BPF_DISP16 plus corresponding ELF
relocation R_BPF_GNU_64_16 are added to the BPF BFD port. These
relocations are used for section-relative 16-bit offsets used in
load/store instructions.
* The disassembler now has support for the "pseudo-c" assembly syntax of
BPF. What dialect to use when disassembling is controlled by a command
line option.
* The disassembler now has support for dumping instruction immediates in
either octal, hexadecimal or decimal. The used output base is controlled
by a new command-line option.
* The GAS BPF test suite has been re-structured and expanded in order to
test the disassembler pseudoc syntax support. Minor bugs have been also
fixed there. The assembler generic tests that were disabled for bpf-*-*
targets due to the previous implementation of pseudoc syntax are now
re-enabled. Additional tests have been added to test the new features of
the assembler. .dump files are no longer used.
* The linker BPF test suite has been adapted to the command line options
used by the new disassembler.
The result is very satisfactory. This patchs adds 3448 lines of code
and removes 10542 lines of code.
Tested in:
* Target bpf-unknown-none with 64-bit little-endian host and 32-bit
little-endian host.
* Target x86-64-linux-gnu with --enable-targets=all
Note that I have not tested in a big-endian host yet. I will do so
once this lands upstream so I can use the GCC compiler farm.
I have not included ChangeLog entries in this patch: these would be
massive and not very useful, considering this is pretty much a rewrite
of the port. I beg the indulgence of the global maintainers.
Bring disassembly back in line with what the assembler accepts, thus
also making it self-consistent (with, in particular selector load/store
insns). While there further add D to all affected insns except ARPL
(where S is used, matching LAR/LSL), to also behave correctly in suffix-
always mode.
While there also hook up the Intel variant of the LKGS test.
For whatever reason in c9f5b96bda ("x86: correct handling of LAR and
LSL") I didn't realize that we can easily use Sv instead of going
through mod_table[]. Redo this aspect of that change.
This patch support Zcb extension, contains new compressed instructions,
some instructions depend on other existed extension, like 'zba', 'zbb'
and 'zmmul'. Zcb also imply Zca extension to enable the compressing
features.
Co-Authored by: Charlie Keaney <charlie.keaney@embecosm.com>
Co-Authored by: Mary Bennett <mary.bennett@embecosm.com>
Co-Authored by: Nandni Jamnadas <nandni.jamnadas@embecosm.com>
Co-Authored by: Sinan Lin <sinan.lin@linux.alibaba.com>
Co-Authored by: Simon Cook <simon.cook@embecosm.com>
Co-Authored by: Shihua Liao <shihua@iscas.ac.cn>
Co-Authored by: Yulong Shi <yulong@iscas.ac.cn>
bfd/ChangeLog:
* elfxx-riscv.c (riscv_multi_subset_supports): New extension.
(riscv_multi_subset_supports_ext): Ditto.
gas/ChangeLog:
* config/tc-riscv.c (validate_riscv_insn): New operators.
(riscv_ip): Ditto.
* testsuite/gas/riscv/zcb.d: New test.
* testsuite/gas/riscv/zcb.s: New test.
include/ChangeLog:
* opcode/riscv-opc.h (MATCH_C_LBU): New opcode.
(MASK_C_LBU): New mask.
(MATCH_C_LHU): New opcode.
(MASK_C_LHU): New mask.
(MATCH_C_LH): New opcode.
(MASK_C_LH): New mask.
(MATCH_C_SB): New opcode.
(MASK_C_SB): New mask.
(MATCH_C_SH): New opcode.
(MASK_C_SH): New mask.
(MATCH_C_ZEXT_B): New opcode.
(MASK_C_ZEXT_B): New mask.
(MATCH_C_SEXT_B): New opcode.
(MASK_C_SEXT_B): New mask.
(MATCH_C_ZEXT_H): New opcode.
(MASK_C_ZEXT_H): New mask.
(MATCH_C_SEXT_H): New opcode.
(MASK_C_SEXT_H): New mask.
(MATCH_C_ZEXT_W): New opcode.
(MASK_C_ZEXT_W): New mask.
(MATCH_C_NOT): New opcode.
(MASK_C_NOT): New mask.
(MATCH_C_MUL): New opcode.
(MASK_C_MUL): New mask.
(DECLARE_INSN): New opcode.
* opcode/riscv.h (EXTRACT_ZCB_BYTE_UIMM): New inline func.
(EXTRACT_ZCB_HALFWORD_UIMM): Ditto.
(ENCODE_ZCB_BYTE_UIMM): Ditto.
(ENCODE_ZCB_HALFWORD_UIMM): Ditto.
(VALID_ZCB_BYTE_UIMM): Ditto.
(VALID_ZCB_HALFWORD_UIMM): Ditto.
(enum riscv_insn_class): New extension class.
opcodes/ChangeLog:
* riscv-dis.c (print_insn_args): New operators.
* riscv-opc.c: New instructions.
First of all it is entirely unclear why THREE_BYTE_TABLE_PREFIX() was
introduced by bf890a93a7. Nothing uses the .prefix_requirement values
from the two relevant entries.
And then having VEX_Cn_TABLE() and friends take arguments is misleading.
These aren't used (or pointlessly used in the case of VEX_C5_TABLE); the
respective table index is decoded from the insn (or implied in the case
of VEX_C5_TABLE).
Several already use OP_R(), which rejects the memory forms of insns, and
a few others can easily be converted to do so as well. Note that for it
to be able to use BadOp() without forward declaration, OP_Skip_MODRM() is
moved down.
While there add the previously missing PREFIX_OPCODE to legacy opcode
0FD7.
Now that we have OP_R(), use it here as well, while wiring memory-only
operands to OP_M() at the same time. To keep the number of consumed
opcode bytes similar to before, make BadOp() also account for VEX/XOP/
EVEX prefix bytes. To keep that change simple, convert need_vex to an
actual count of prefix bytes (keeping intact all prior boolean uses of
the field).
Note how this improves disassembly of such bad encodings, by at least
leaving a hint towards what a "nearby" instruction is. (For KSHIFT*
change the immediates test testcases use, such that disassembly remains
sufficiently in sync.)
While there also use Ux for VPMOV{B,W,D,Q}2M, where decoding through
mod_table[] was missing in the earlier scheme.
Fold OP_MS() and OP_XS() into OP_R(), paralleling OP_M(). Use operand
names (largely) matching those in the SDM. For 128-bit-only forms use
Uxmm though, marking 256-bit forms as bad. This then allows no longer
going through vex_len_table[] for two of the insns.
Specifically _do not_ continue to mis-use v_mode.
Several already use OP_M(), which rejects the register forms of insns,
and a few others can easily be converted to do so as well. (Note that
FXSAVE_Fixup() wires through to OP_M(). Note further that OP_IndirE(),
which wasn't placed very well anyway, is moved down to avoid the need to
forward-declare BadOp().)
Also adjust formatting of and drop PREFIX_OPCODE from a few adjacent
entries.
Most of them use Mx already for the memory operand, which rejects the
register form of the insn. Use that operand type also for the two EVEX
forms which so far have used EXEvexXNoBcst (and thus failed to reject
the register forms), compensating by flagging broadcast as bad for all
Mx. This way several other insns which don't permit embedded broadcast
either are also covered at the same time.
By changing decode order to do ModR/M.mod last (rather than VEX.L), the
VEX entries (which are already reused by EVEX decoding) can be folded
with their legacy counterparts as well. Note how this change of decode
order also allows removing two auxiliary #define-s, which were
introduced during earlier folding (because of that unhelpful order of
steps).
Introduce macro V to expand to 'v' in the VEX/EVEX case, and replace a
couple of abort()s where legacy code can now legitimately make it. While
there for {,V}LDDQU drop hoing through mod_table[] - OP_M() rejects
register operands quite fine.
Masking is not permitted for certain further insns, not falling in any
of the earlier categories. Introduce the Y macro (not expanding to any
output) to flag such cases.
Note that in a few cases entries already covered otherwise are converted
as well, to continue to allow sharing of the string literals.
Masking is not permitted in this case. See the code comment for how this
is being dealt with.
To avoid excess special casing of modes, have OP_M() call OP_E_memory()
directly.
While only zeroing-masking is possible in this case, this still requires
EVEX.z to be clear. Introduce a "global" flag right here, to be re-used
by checks which need to live in specific operand handlers.
Rather than corrupting disassmbly altogether, flag EVEX.z set as bad
when masking isn't in effect in the first place at the time the
destination operand is actually processed.
opcodes/ChangeLog:
* loongarch-opc.c: Mark the offset operands as "so" for
{,x}v{ld,st}, {,x}v{ldrepl,stelm}.[bhwd], and {ld,st}[lr].[wd].
Signed-off-by: WANG Xuerui <git@xen0n.name>
Zvksh is part of the vector crypto extensions.
This extension adds the following instructions:
- vsm3me.vv
- vsm3c.vi
bfd/ChangeLog:
* elfxx-riscv.c (riscv_multi_subset_supports): Add instruction
class support for Zvksh.
(riscv_multi_subset_supports_ext): Likewise.
gas/ChangeLog:
* testsuite/gas/riscv/zvksh.d: New test.
* testsuite/gas/riscv/zvksh.s: New test.
include/ChangeLog:
* opcode/riscv-opc.h (MATCH_VSM3C_VI): New.
(MASK_VSM3C_VI): New.
(MATCH_VSM3ME_VV): New.
(MASK_VSM3ME_VV): New.
(DECLARE_INSN): New.
* opcode/riscv.h (enum riscv_insn_class): Add instruction class
support for Zvksh.
opcodes/ChangeLog:
* riscv-opc.c: Add Zvksh instructions.
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
Zvksed is part of the vector crypto extensions.
This extension adds the following instructions:
- vsm4k.vi
- vsm4r.[vv,vs]
bfd/ChangeLog:
* elfxx-riscv.c (riscv_multi_subset_supports): Add instruction
class support for Zvksed.
(riscv_multi_subset_supports_ext): Likewise.
gas/ChangeLog:
* testsuite/gas/riscv/zvksed.d: New test.
* testsuite/gas/riscv/zvksed.s: New test.
include/ChangeLog:
* opcode/riscv-opc.h (MATCH_VSM4K_VI): New.
(MASK_VSM4K_VI): New.
(MATCH_VSM4R_VS): New.
(MASK_VSM4R_VS): New.
(MATCH_VSM4R_VV): New.
(MASK_VSM4R_VV): New.
(DECLARE_INSN): New.
* opcode/riscv.h (enum riscv_insn_class): Add instruction class
support for Zvksed.
opcodes/ChangeLog:
* riscv-opc.c: Add Zvksed instructions.
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
Zvknh[a,b] are parts of the vector crypto extensions.
This extension adds the following instructions:
- vsha2ms.vv
- vsha2c[hl].vv
bfd/ChangeLog:
* elfxx-riscv.c (riscv_multi_subset_supports): Add instruction
class support for Zvknh[a,b].
(riscv_multi_subset_supports_ext): Likewise.
gas/ChangeLog:
* testsuite/gas/riscv/zvknha.d: New test.
* testsuite/gas/riscv/zvknha_zvknhb.s: New test.
* testsuite/gas/riscv/zvknhb.d: New test.
include/ChangeLog:
* opcode/riscv-opc.h (MATCH_VSHA2CH_VV): New.
(MASK_VSHA2CH_VV): New.
(MATCH_VSHA2CL_VV): New.
(MASK_VSHA2CL_VV): New.
(MATCH_VSHA2MS_VV): New.
(MASK_VSHA2MS_VV): New.
(DECLARE_INSN): New.
* opcode/riscv.h (enum riscv_insn_class): Add instruction class
support for Zvknh[a,b].
opcodes/ChangeLog:
* riscv-opc.c: Add Zvknh[a,b] instructions.
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
Zvkg is part of the vector crypto extensions.
This extension adds the following instructions:
- vghsh.vv
- vgmul.vv
bfd/ChangeLog:
* elfxx-riscv.c (riscv_multi_subset_supports): Add instruction
class support for Zvkg.
(riscv_multi_subset_supports_ext): Likewise.
gas/ChangeLog:
* testsuite/gas/riscv/zvkg.d: New test.
* testsuite/gas/riscv/zvkg.s: New test.
include/ChangeLog:
* opcode/riscv-opc.h (MATCH_VGHSH_VV): New.
(MASK_VGHSH_VV): New.
(MATCH_VGMUL_VV): New.
(MASK_VGMUL_VV): New.
(DECLARE_INSN): New.
* opcode/riscv.h (enum riscv_insn_class): Add instruction class
support for Zvkg.
opcodes/ChangeLog:
* riscv-opc.c: Add Zvkg instructions.
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
This patch adds support for the RISC-V Zfa extension,
which introduces additional floating-point instructions:
* fli (load-immediate) with pre-defined immediates
* fminm/fmaxm (like fmin/fmax but with different NaN behaviour)
* fround/froundmx (round to integer)
* fcvtmod.w.d (Modular Convert-to-Integer)
* fmv* to access high bits of FP registers in case XLEN < FLEN
* fleq/fltq (quiet comparison instructions)
Zfa defines its instructions in combination with the following
extensions:
* single-precision floating-point (F)
* double-precision floating-point (D)
* quad-precision floating-point (Q)
* half-precision floating-point (Zfh)
This patch is based on an earlier version from Tsukasa OI:
https://sourceware.org/pipermail/binutils/2022-September/122939.html
Most significant change to that commit is the switch from the rs1-field
value to the actual floating-point value in the last operand of the fli*
instructions. Everything that strtof() can parse is accepted and
the '%a' printf specifier is used to output hex floating-point literals
in the disassembly.
The Zfa specification is frozen (and has passed public review). It is
available as a chapter in "The RISC-V Instruction Set Manual: Volume 1":
https://github.com/riscv/riscv-isa-manual/releases
bfd/ChangeLog:
* elfxx-riscv.c (riscv_multi_subset_supports): Add instruction
class support for 'Zfa' extension.
(riscv_multi_subset_supports_ext): Likewise.
(riscv_implicit_subsets): Add 'Zfa' -> 'F' dependency.
gas/ChangeLog:
* config/tc-riscv.c (flt_lookup): New helper to lookup a float value
in an array.
(validate_riscv_insn): Add 'Wfv' as new format string directive.
(riscv_ip): Likewise.
* doc/c-riscv.texi: Add floating-point chapter and describe
limiations of the Zfa FP literal parsing.
* testsuite/gas/riscv/zfa-32.d: New test.
* testsuite/gas/riscv/zfa-32.s: New test.
* testsuite/gas/riscv/zfa-64.d: New test.
* testsuite/gas/riscv/zfa-64.s: New test.
* testsuite/gas/riscv/zfa-fail.d: New test.
* testsuite/gas/riscv/zfa-fail.l: New test.
* testsuite/gas/riscv/zfa-fail.s: New test.
* testsuite/gas/riscv/zfa.d: New test.
* testsuite/gas/riscv/zfa.s: New test.
* testsuite/gas/riscv/zfa.s: New test.
* opcode/riscv-opc.h (MATCH_FLI_H): New.
(MASK_FLI_H): New.
(MATCH_FMINM_H): New.
(MASK_FMINM_H): New.
(MATCH_FMAXM_H): New.
(MASK_FMAXM_H): New.
(MATCH_FROUND_H): New.
(MASK_FROUND_H): New.
(MATCH_FROUNDNX_H): New.
(MASK_FROUNDNX_H): New.
(MATCH_FLTQ_H): New.
(MASK_FLTQ_H): New.
(MATCH_FLEQ_H): New.
(MASK_FLEQ_H): New.
(MATCH_FLI_S): New.
(MASK_FLI_S): New.
(MATCH_FMINM_S): New.
(MASK_FMINM_S): New.
(MATCH_FMAXM_S): New.
(MASK_FMAXM_S): New.
(MATCH_FROUND_S): New.
(MASK_FROUND_S): New.
(MATCH_FROUNDNX_S): New.
(MASK_FROUNDNX_S): New.
(MATCH_FLTQ_S): New.
(MASK_FLTQ_S): New.
(MATCH_FLEQ_S): New.
(MASK_FLEQ_S): New.
(MATCH_FLI_D): New.
(MASK_FLI_D): New.
(MATCH_FMINM_D): New.
(MASK_FMINM_D): New.
(MATCH_FMAXM_D): New.
(MASK_FMAXM_D): New.
(MATCH_FROUND_D): New.
(MASK_FROUND_D): New.
(MATCH_FROUNDNX_D): New.
(MASK_FROUNDNX_D): New.
(MATCH_FLTQ_D): New.
(MASK_FLTQ_D): New.
(MATCH_FLEQ_D): New.
(MASK_FLEQ_D): New.
(MATCH_FLI_Q): New.
(MASK_FLI_Q): New.
(MATCH_FMINM_Q): New.
(MASK_FMINM_Q): New.
(MATCH_FMAXM_Q): New.
(MASK_FMAXM_Q): New.
(MATCH_FROUND_Q): New.
(MASK_FROUND_Q): New.
(MATCH_FROUNDNX_Q): New.
(MASK_FROUNDNX_Q): New.
(MATCH_FLTQ_Q): New.
(MASK_FLTQ_Q): New.
(MATCH_FLEQ_Q): New.
(MASK_FLEQ_Q): New.
(MATCH_FCVTMOD_W_D): New.
(MASK_FCVTMOD_W_D): New.
(MATCH_FMVH_X_D): New.
(MASK_FMVH_X_D): New.
(MATCH_FMVH_X_Q): New.
(MASK_FMVH_X_Q): New.
(MATCH_FMVP_D_X): New.
(MASK_FMVP_D_X): New.
(MATCH_FMVP_Q_X): New.
(MASK_FMVP_Q_X): New.
(DECLARE_INSN): New.
* opcode/riscv.h (enum riscv_insn_class): Add instruction
classes for the Zfa extension.
opcodes/ChangeLog:
* riscv-dis.c (print_insn_args): Add support for
new format string directive 'Wfv'.
* riscv-opc.c: Add Zfa instructions.
Co-Developed-by: Tsukasa OI <research_trasio@irq.a4lg.com>
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
Co-Developed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
As outlined in the LoongArch ELF psABI spec [1], it is actually already
2 versions after the initial LoongArch support, and the $v[01] and
$fv[01] names should really get sunset by now.
In addition, the "$x" name for $r21 was never included in any released
version of the ABI spec, and such usages are all fixed to say just $r21
for every project I could think of that accepted a LoongArch port.
Plus, the upcoming LSX/LASX support makes use of registers named
"$vrNN" and "$xrNN", so having "$vN" and "$x" alongside would almost
certainly create confusion for developers.
Issue warnings for such usages per the deprecation procedure detailed
in the spec, so we can finally remove support in the next release cycle
after this.
[1]: https://loongson.github.io/LoongArch-Documentation/LoongArch-ELF-ABI-EN.html
gas/ChangeLog:
* config/tc-loongarch.c: Init canonical register ABI name
mappings and deprecated register names.
(loongarch_args_parser_can_match_arg_helper): Warn in case of
deprecated register name usage.
* testsuite/gas/loongarch/deprecated_reg_aliases.d: New test.
* testsuite/gas/loongarch/deprecated_reg_aliases.l: Likewise.
* testsuite/gas/loongarch/deprecated_reg_aliases.s: Likewise.
include/ChangeLog:
* opcode/loongarch.h: Rename global variables.
opcodes/ChangeLog:
* loongarch-opc.c: Rename the alternate/deprecated register name
mappings, and move $x to the deprecated name map.
Signed-off-by: WANG Xuerui <git@xen0n.name>
For better round-trip fidelity and readability in general.
gas/ChangeLog:
* testsuite/gas/loongarch/uleb128.d: Update test case.
* testsuite/gas/loongarch/raw-insn.d: New test.
* testsuite/gas/loongarch/raw-insn.s: Likewise.
opcodes/ChangeLog:
* loongarch-dis.c (disassemble_one): Print ".word" if !opc.
Signed-off-by: WANG Xuerui <git@xen0n.name>
The additional hex notation was minimally useful when one had to
inspect code with heavy bit manipulation, or of unclear signedness, but
it clutters the output, and the style is not regular assembly language
syntax either.
Precisely how one approaches the original use case is not taken care of
in this patch (maybe we want a disassembler option forcing a certain
style for immediates, like for example printing every immediate in
decimal or hexadecimal notation), but at least let's stop the current
practice.
ChangeLog:
* testsuite/gas/loongarch/imm_ins.d: Update test case.
* testsuite/gas/loongarch/imm_ins_32.d: Likewise.
* testsuite/gas/loongarch/imm_op.d: Likewise.
* testsuite/gas/loongarch/jmp_op.d: Likewise.
* testsuite/gas/loongarch/load_store_op.d: Likewise.
* testsuite/gas/loongarch/macro_op.d: Likewise.
* testsuite/gas/loongarch/macro_op_32.d: Likewise.
* testsuite/gas/loongarch/privilege_op.d: Likewise.
* testsuite/gas/loongarch/uleb128.d: Likewise.
* testsuite/gas/loongarch/vector.d: Likewise.
ld/ChangeLog:
* testsuite/ld-loongarch-elf/jmp_op.d: Update test case.
* testsuite/ld-loongarch-elf/macro_op.d: Likewise.
* testsuite/ld-loongarch-elf/macro_op_32.d: Likewise.
opcodes/ChangeLog:
* loongarch-dis.c (dis_one_arg): Remove the "(0x%x)" part from
disassembly output of signed immediate operands.
Signed-off-by: WANG Xuerui <git@xen0n.name>
Add a modifier char 'o' telling the disassembler to print the immediate
using the address offset style, and mark the memory access instructions'
offset operands as such.
opcodes/ChangeLog:
* loongarch-dis.c (dis_one_arg): Style disassembled address
offsets as such when the operand has a modifier char 'o'.
* loongarch-opc.c: Add 'o' to operands that represent address
offsets.
Signed-off-by: WANG Xuerui <git@xen0n.name>
